NVT210DMTR2G【PDF 13/20 页】IC TEMP SENSOR DGTL 8-WDFN

收藏本站

您好，
买卖IC网欢迎您。
请登录
免费注册

买卖IC网

Sheet目录46

9页 10页 11页 12页 [13页]14页 15页 16页 17页

NVT210

http://onsemi.com

write operation is limited only by what the master

and slave devices can handle.

3. When all data bytes have been read or written,

stop conditions are established. In write mode, the

master pulls the data line high during the tenth

clock pulse to assert a stop condition. In read

mode, the master device overrides the

acknowledge bit by pulling the data line high

during the low period before the ninth clock pulse.

This is known as no acknowledge. The master

takes the data line low during the low period

before the tenth clock pulse, then high during the

tenth clock pulse to assert a stop condition.

Any number of bytes of data are transferable over

the serial bus in one operation, but it is not

possible to mix read and write in one operation

because the type of operation is determined at the

beginning and cannot subsequently be changed

without starting a new operation. For the NVT210,

write operations contain either one or two bytes,

while read operations contain one byte.

To write data to one of the device data registers, or to read

data from it, the address pointer register must be set so that

the correct data register is addressed. The first byte of a write

operation always contains a valid address that is stored in the

address pointer register. If data is to be written to the device,

the write operation contains a second data byte that is written

to the register selected by the address pointer register.

This procedure is illustrated in Figure 15. The device

address is sent over the bus followed by R/W

set to 0. This

is followed by two data bytes. The first data byte is the

address of the internal data register to be written to, which

is stored in the address pointer register. The second data byte

is the data to be written to the internal data register.

Figure 15. Writing a Register Address to the Address Pointer Register, then Writing Data to the Selected Register

SCLK

SDATA

A5 A4 A3 A2 A1 A0

D7 D6 D5 D4 D3 D2 D1 D0

ACK. BY

NVT210

START BY

MASTER

ACK. BY

NVT210

D7 D6 D5 D4 D3 D2 D1 D0

ACK. BY

NVT210

STOP BY

MASTER

SCLK (CONTINUED)

SDATA (CONTINUED)

FRAME 1

SERIAL BUS ADDRESS BYTE

FRAME 2

ADDRESS POINTER REGISTER BYTE

FRAME 3

DATA BYTE

R/W

Figure 16. Writing to the Address Pointer Register Only

SCLK

SDATA

A5 A4 A3 A2 A1 A0

D5 D4 D3 D2 D1 D0

ACK. BY

NVT210

STOP BY

MASTER

START BY

MASTER

FRAME 1

SERIAL BUS ADDRESS BYTE

FRAME 2

ADDRESS POINTER REGISTER BYTE

ACK. BY

NVT210

R/W

Figure 17. Reading Data from a Previously Selected Register

SCLK

SDATA

A5 A4 A3 A2 A1 A0

D7 D6 D5 D4 D3 D2 D1 D0

ACK. BY

NVT210

STOP BY

MASTER

START BY

MASTER

FRAME 1

SERIAL BUS ADDRESS BYTE

FRAME 2

ADDRESS POINTER REGISTER BYTE

ACK. BY

NVT210

R/W

发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

*型号	*数量	厂商	批号	封装

添加更多采购

采购需求

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

我的联系方式